Class B airspace is typically airspace from the floor to 10,000 feet MSL surrounding the nation's busiest airports in terms of airport operations or passenger enplanements.
How do you discover Class B airspace boundaries?Class B airspace is surrounded by way of what's recognised as a "Mode-C veil." The Mode-C veil is marked by a thick magenta ring, with the phrases "30 NM MODE C" subsequent to it. What does it mean? The Mode-C veil is NOT section of Class B airspace, however, any flight inside the veil requires you to use a Mode-C transponder.
How are the altitude boundaries of Class B airspace displayed on sectional charts?On your sectional, horizontal Class B airspace limits are outlined in concentric solid blue circular strains that may additionally be indented or extended in certain locations due to geography or air visitors routes. The pinnacle and backside of every layer of airspace, as you can see, are given in what looks like a fraction; for example, 90/40.
Learn more about airspace boundaries here;
https://brainly.com/question/30549884
#SPJ4
purpose of fuel reservoir tank c172
High wing aircraft the Cessna 172SP (C172) uses a gravity fed fuel delivery system to the fuel injected engine.
What size is the Cessna 172's fuel tank?Two fuel tanks are on the Cessna 172S. Each wing has a tank installed on it. 56 gallons of fuel can be stored in 56 tanks, each of which contains 28 gallons.
How does a Cessna 172's fuel system operate?High wing aircraft the Cessna 172SP (C172) uses a gravity fed fuel delivery system to the fuel injected engine. The two tanks inside the two wings are where the fuel is supplied. either the fuel from both tanks, or Afterward, just one makes it to the fuel selector tank.
To know more about fuel reservoir tank visit:-
https://brainly.com/question/14776737
#SPJ4
when must a competent person conduct an inspection of a sling?
Before each use and at least once every 12 months, a sling must be inspected by a qualified person.
What is a sling?An arm that has been hurt is supported with a sling, a bandage. Applying a sling Hold the arm still above and below the injury.
To create the sling, place the triangle bandage beneath the hurt arm and over the shoulder that is not hurt. Sling ends should be tied at the side of the neck.
A competent person should also examine a sling following any incident that might compromise its integrity, such as dropping it or exposing it to a potentially damaging environment.
Learn more about sling here:
https://brainly.com/question/14695112
#SPJ1
A competent person inspects a sling before each use and upon change in application. Periodic inspections are conducted based on frequency and conditions of use. If wear or damage is detected, the sling is removed from service.
Explanation:A
competent person
must conduct an inspection of a sling before each shift begins and whenever there is a change in the sling's application that could affect its operation. Additionally, a
periodic inspection
should be performed at intervals based on frequency of use, severity of service conditions, nature of lifts being made, and experience gained from the service life of slings used in similar circumstances. Factors to consider include visible damage, wear, deformation and increase in length. If any of these are detected, the sling should be removed from service.
Learn more about sling inspection here:https://brainly.com/question/31623403
Consider the following classes.
public class Bird
{
public void sing()
{
System.out.println("Cheep");
}
}
public class Duck extends Bird
{
public void sing()
{
System.out.println("Quack");
}
}
public class Chicken extends Bird
{
// No methods defined
}
public class Rooster extends Chicken
{
public void sing()
{
System.out.println("Cockadoodle doo");
}
}
The following statement appears in a method in another class.
someBird.sing();
Under which of the following conditions will the statement compile and run without error?
When someBird has been declared as type Duck
When someBird has been declared as type Chicken
When someBird has been declared as type Rooster
A: I only
B: III only
C: I and II only
D: I and III only
E: I, II, and III
The statement "someBird.sing();" will compile and run without error under the conditions when "someBird" has been declared as type Duck or type Rooster. Therefore, the correct answer is option D: I and III only.
What is the rationale for the above response?The classes Duck and Rooster have overridden the "sing" method of the parent class Bird, whereas the class Chicken has not defined the "sing" method.
Therefore, if "someBird" is declared as type Duck or type Rooster, the compiler will know that these classes have the "sing" method and will use the overridden method. If "someBird" is declared as type Chicken, it will still compile, but it will use the "sing" method of the parent class Bird since Chicken does not override this method.
Learn more about compile at:
https://brainly.com/question/28232020
#SPJ1
the thickness of a milled blank is listed below in millimeters. 15.02 15.04 15.07 15.08 15.09 find the range, sample standard deviation, and sample variance.
The thickness of a milled blank is listed below in millimeters are
Range: 15.02 - 15.09,Sample Standard Deviation: 0.04,Sample Variance: 0.0016.
What is the millimeters ?Millimeters (mm) are a unit of measure in the metric system. They are used to measure length, width, and depth. One millimeter is equal to 0.1 centimeters, or 0.001 meters. Millimeters are often used to measure small distances and components. For example, they are commonly used in the manufacturing of electronics, measuring the thickness of a sheet of metal, or measuring the length of a screw. Millimeters are also used to measure the size of small objects such as coins, beads and jewelry.
To learn more about millimeters
https://brainly.com/question/13426998
#SPJ1
A ? has three leads identified as base, collector, and emitter. BJT (base-emitter junction)
The base-collector junction is reverse-biased, while the base-emitter junction is forward-biased. The majority of bipolar transistors are built to have the highest forward-active mode (F) common-emitter current gain possible.
If so, the collector-emitter current will be substantially greater for minor base current fluctuations while still being roughly proportional to the base current. For the transistor to operate in the active state, the emitter-base junction must be forward biased and the collector-base junction must be reversed-biased.
As the first junction is forwardly biased, the majority of the current flows through it and travels to the base, but the second junction needs to be reversely biased in order to reach the collector.
While the collector-to-base junction is reverse-biased, the emitter-to-base junction is forward-biased. The electrons from the N-type emitter travel toward the forward bias at the emitter to the base junction. This circumstance determines the emitter current (IE).
To know more about current:
brainly.com/question/29766827
#SPJ4
when a square wave is applied to an integrator op amp, the output is a(n) __________.
A square wave applied to an integrator op amp produces an inverted and amplified square wave as the output.
What takes place if you are caught in a square wave?For the simple fact that they originate from two separate directions and most likely from two different weather systems, square waves are hazardous. Hence, strong and opposing currents are present along with them. As a result, both strong coupled currents and rip currents may develop.
Why does a square wave exist?A periodic wave known as a square wave alternates between two fixed amplitudes for equal periods of time. Not at the middle voltage, but at one of two extreme voltages, a square wave begins.
To know more about amplified visit:-
https://brainly.com/question/17027304
#SPJ4
non-motorized vehicles are allowed on expressways.truefalse
Answer:
True
Explanation:
Non-motorized vehicles are allowed on expressways.
Some expressways even have bike lanes to keep them from traveling on the side if the road.
what is the first step in shaping a pigeon’s peck to a plastic disc?
The first step in shaping a pigeon's peck into a plastic disc is shaping the response of eating from the food tray.
Which of the following exemplifies shaping best?When a baby or toddler learns to walk, for example, shaping occurs. They are strengthened for crawling, standing, taking one step, several steps, and finally walking. The child's parents typically provide reinforcement in the form of a lot of praise and attention.
What is an illustration of this? When a pigeon pecks a key for food, it does so with its eyes and mouth slightly open.' Later it pecks the key since it needs to do as such to acquire food. One type of classical conditioning known as AutoShaping is compatible with Pavlov's stimulus-substitution theory: The key light seems to take the place of food because it is associated with food, and the bird is attempting to consume it.
To know more about pigeon's peck visit :-
https://brainly.com/question/28171043
#SPJ4
Which of these inputlookup expressions is invalid?
a) | inputlookup map.kml
b) | inputlookup file.csv.gz
c) | inputlookup map_lookup
d) | inputlookup file.csv
The invalid inputlookup expression is (b) | inputlookup file.csv.gz.
What is inputlookup command?
The inputlookup command is used in Splunk to retrieve data from a lookup file and use it in a search.
In the given expressions, options (a), (c), and (d) are valid inputlookup expressions because they use the correct syntax for the command and refer to existing lookup files in the system.
However, option (b) is not a valid inputlookup expression because it refers to a file with a .gz extension.
The inputlookup command can only retrieve data from files in CSV or KV format, and it does not support compressed files. Therefore, the correct expression for this scenario would be:
| inputlookup file.csv
This expression retrieves data from the file named "file.csv" and uses it in the search.
To know more about Splunk, visit: https://brainly.com/question/30330547
#SPJ1
Two cables BG and BH are attached to frame ACD as shown. Knowing that the tension in cable BG is 550N determine the components of the force exerted by cable BG on the frame at B. 0.56 m 1.4 m 0 1.48 m 1.2 m 1.2 m 0.8 m B 0.8 mC The component of the force in the x-direction is The component of the force in the y-direction is The component of the force in the z-direction is N. N. N
The components of the force exerted by cable BG on the frame at B are 1.2 N in the x-direction and 0.8 N in the y-direction.The component of the force in the z-direction is zero, since cable BG is not exerting any force in that direction.
What is component of force?The component of force is the part of a force that acts in a specific direction. A force acting in three-dimensional space can be broken down into its components in the x, y, and z directions. The x-component is the part of the force that acts in the horizontal (left or right) direction, the y-component is the part of the force that acts in the vertical (up or down) direction, and the z-component is the part of the force that acts in the depth (forward or backward) direction.
Since we are given the tension in cable BG, we can use trigonometry to find the components of the force exerted by cable BG on the frame at B. Let's call the angle between cable BG and the horizontal axis θ.
Using trigonometry, we can find that:
sin(θ) = opposite/hypotenuse = BC/BG
cos(θ) = adjacent/hypotenuse = BG/BD
We are given that BC = 0.8 m, BD = 1.2 m, and BG = 550 N.
Therefore, we can calculate the components of the force as follows:
The component of the force in the x-direction is:
Fx = BG cos(θ) = 550 cos(θ) = 550(BD/BG) = 550(1.2/550) = 1.2 N (rounded to one decimal place)
The component of the force in the y-direction is:
Fy = BG sin(θ) = 550 sin(θ) = 550(BC/BG) = 550(0.8/550) = 0.8 N
To know more about cable visit:
https://brainly.com/question/10932960
#SPJ1
What kind of statement allows us to run one block of code if one condition is true, and a separate block of code otherwise?
A. if statement
B. break statement
C. if/else statement
D. for loop
The true and false parts of a given condition are both executed using the if-else expression. If the condition is true, the code in the if block is performed; if it is false, the code in the else block is executed.
The term "executed" means what exactly?
As a kind of punishment, one may be executed: He was put to death for killing. Following two weeks, she was put to death and executed. Yesterday, a killer with a death sentence was executed in North Carolina.
Execute has a number of popular synonyms, including attain, effectuate, discharge, and perform. Despite the fact that all of these phrases indicate "to carry out or into effect," the term "execute" emphasises doing what is intended or in the plan.
Know more about discharge Visit:
https://brainly.com/question/29571800
#SPJ4
Using the data presented in Fig. 7-5 (to determine the peak/mean ratio with respect to the volume), estimate the size of a container to be used with a gravity chute for a 24-story apartment building with 192 individual living units if the container will be emptied daily. Assume that the average occupancy rate for each living unit is 3.1 persons.
The answer is given below.
Describe Volume ?In general, a volume refers to the amount of space that an object takes up. In the context of computing, specifically data storage, a volume refers to a logical partition or container that is used to store and organize data on a storage device, such as a hard drive or a flash drive.
Volumes can be created and managed by the operating system or by a storage management software, and they can be formatted with a file system that allows the user to access and manage the stored data. Volumes can be of different sizes and can be allocated to different applications or users.
In cloud computing, a volume refers to a virtual storage device that is allocated to a cloud server instance. This allows the server to store and access data independent of the underlying hardware, and enables the user to scale storage capacity up or down as needed.
Volumes can be used for a variety of purposes, including storing data backups, hosting databases, and serving as a file system for an operating system. Overall, volumes are a key component of data storage and management in modern computing.
Assuming a typical peak/mean ratio of 1.5, we can estimate the size of the container required for a 24-story apartment building with 192 individual living units.
Assuming an average occupancy rate of 3.1 persons per living unit, the total number of people in the building would be:
192 living units * 3.1 persons per living unit = 595.2 people
Assuming that each person generates 4.5 pounds of waste per day, the total amount of waste generated by the building would be:
595.2 people * 4.5 pounds of waste per person per day = 2678.4 pounds of waste per day
Assuming that the container needs to be emptied daily, the size of the container required can be estimated using the following formula:
Container volume = Waste volume per day * Peak/mean ratio
Assuming a typical peak/mean ratio of 1.5, the container volume required would be:
Container volume = 2678.4 pounds of waste per day * 1.5 = 4017.6 pounds of waste
Assuming a density of 30 pounds per cubic foot for the waste, the container volume required would be:
Container volume = 4017.6 pounds of waste / 30 pounds per cubic foot = 133.92 cubic feet
Therefore, a container with a volume of approximately 133.92 cubic feet would be required for a 24-story apartment building with 192 individual living units assuming a typical peak/mean ratio of 1.5. However, it is important to note that this estimate is based on several assumptions and the actual size of the container required may vary depending on the specific circumstances of the building.
To know more about volume visit:
https://brainly.com/question/23477586
#SPJ1
Volumes can be created and managed by the operating system or by a storage management software, and they can be formatted with a file system that allows the user to access and manage the stored data. Volumes can be of different sizes and can be allocated to different applications or users.
Describe Volume ?In general, a volume refers to the amount of space that an object takes up. In the context of computing, specifically data storage, a volume refers to a logical partition or container that is used to store and organize data on a storage device, such as a hard drive or a flash drive.
In cloud computing, a volume refers to a virtual storage device that is allocated to a cloud server instance. This allows the server to store and access data independent of the underlying hardware, and enables the user to scale storage capacity up or down as needed.
Volumes can be used for a variety of purposes, including storing data backups, hosting databases, and serving as a file system for an operating system. Overall, volumes are a key component of data storage and management in modern computing.
Assuming a typical peak/mean ratio of 1.5, we can estimate the size of the container required for a 24-story apartment building with 192 individual living units.
Assuming an average occupancy rate of 3.1 persons per living unit, the total number of people in the building would be:
192 living units * 3.1 persons per living unit = 595.2 people
Assuming that each person generates 4.5 pounds of waste per day, the total amount of waste generated by the building would be:
595.2 people * 4.5 pounds of waste per person per day = 2678.4 pounds of waste per day
Assuming that the container needs to be emptied daily, the size of the container required can be estimated using the following formula:
Container volume = Waste volume per day * Peak/mean ratio
Assuming a typical peak/mean ratio of 1.5, the container volume required would be:
Container volume = 2678.4 pounds of waste per day * 1.5 = 4017.6 pounds of waste
Assuming a density of 30 pounds per cubic foot for the waste, the container volume required would be:
Container volume = 4017.6 pounds of waste / 30 pounds per cubic foot = 133.92 cubic feet
Therefore, a container with a volume of approximately 133.92 cubic feet would be required for a 24-story apartment building with 192 individual living units assuming a typical peak/mean ratio of 1.5. However, it is important to note that this estimate is based on several assumptions and the actual size of the container required may vary depending on the specific circumstances of the building.
To know more about volume visit:
brainly.com/question/23477586
#SPJ1
what is the bigger teraflops vs terrahertz?
Teraflops is a measure of computing power, and terrahertz (THz) is a measure of frequency. In terms of size, teraflops is much bigger than terrahertz.
What is teraflops?A teraflop is a unit of computing speed equal to one trillion floating point operations per second (FLOPS). Teraflops are used to measure the speed of a computer's processor and the performance of its hardware. Teraflops are typically used to measure the performance of high-performance computing systems, such as supercomputers, as well as graphics processing units (GPUs) and other specialized hardware. The higher the teraflop count, the faster the computer is capable of performing complex calculations and operations. Teraflops are also used to measure the performance of artificial intelligence (AI) systems, as well as to measure the performance of certain types of scientific calculations.
To learn more about teraflops
https://brainly.com/question/27970979
#SPJ4
Pls help me to build me a robot in tinkerCad Design-1 The first proposed design is based on a robot equipped with an advanced system as well as a robotic arm ideal for preparing and serving meals, especially drinks, in less than 5 mins. Design 2 The second robot design is based on a robot without a robotic arm capable of preparing, seasoning, and serving food autonomously. Design Selection The required design needs to be capable of preparing food as well as set, clearing, and cleaning the table. The following are the design criteria used. ● Price ● Durability ● Aesthetically Pleasing ● Meal Prep Time ● Materials The used scale for the above AHP table involved 1 for least important and 5 for the most important. The table highlights meal preparation design criteria was the most important while Aesthetically Pleasing was the least important. The first design was selected based on the meal preparation time aspect. The second design took longer to prepare a meal. Final Design The first design equipped with a robotic arm is the ideal final design as the arm can help with functions such as clearing and cleaning of tables besides the main function of preparing meals within a short period of time. In this presentation video, each member at/for their allotted time, will showcase their completed individual robot. They will separately present their mechanical design, electrical design, and the software design. The mechanical design will be presented as a detailed CAD model of the robot created by the team member (or just the picture of physical robot if they made one in real-life). The electrical design will be presented as a complete and functioning TinkerCAD circuit (or just the picture of the actual circuit they made in real-life). The software design will be presented as snippets of the functioning Arduino code they wrote in TinkerCAD (or Arduino in real life). They'll also have to show a flowchart showing the overall logic/algorithm of their code. After these, they'll showcase/demonstrate their robot's overall functionality by giving various combinations of sensor inputs and the signals from other robots/central hub. This can be done in TinkerCAD simulation, using the Serial.read(), Serial.print(), and/or the IR remote (or by IR remote, bluetooth, wifi module etc. in real life). Each team member will be individually graded for this part of the presentation. Besides the functionality of individual robots, the team as a whole should show how the robots will behave when collaborating together to accomplish the team task. For this part, they will have to create and present an overall flowchart which considers various inputs/outputs of the robots (and the central hub if needed) and stitch them all together to have a functioning swarm. If you want some extra credit then along with this overall flowchart you should implement its logic as a MATLAB simulation of robots collaborating together in an arena. A sample MATLAB file, along with a video, to simulate the interacting robots is available in week 6.1. Please note, you won't have to write a completely new MATLAB code of your own. The expectation is to understand the existing sample MATLAB code just well enough to be able to modify it for your own use. In the provided MATLAB simulation, the robots are represented by dots and the code (via the central hub) directs them to move based on where each robot is and what each robot is sensing.
To start building your robot in TinkerCad, you can first sketch out the basic design and features of the robot on paper or using a digital drawing tool.
How will sketching help design the robot?This will help you to visualize the overall structure, shape, and size of the robot, as well as its various components such as the robotic arm, sensors, motors, and control systems.
Once you have a rough sketch of your robot, you can then start creating a more detailed 3D model using TinkerCad's design tools.
You can import pre-made components and shapes or create your own custom designs using TinkerCad's extensive library of shapes and tools. You can also add textures, colors, and other aesthetic features to make your robot look more visually appealing.
For the electrical design, you can use TinkerCad's circuit design tool to create a functioning circuit that controls the various components of your robot. You can add sensors, actuators, microcontrollers, and other electronic components to your circuit, and simulate its behavior to ensure that everything is working correctly.
Finally, you can use TinkerCad's software design tools to write the code that controls your robot's behavior. You can use Arduino code or other programming languages to create the logic and algorithms that govern how your robot responds to its environment and performs its tasks.
Once your robot is complete, you can then use TinkerCad's simulation tools to test and refine its functionality. You can simulate different scenarios and sensor inputs to see how your robot responds, and make adjustments as needed to improve its performance.
Overall, building a robot in TinkerCad can be a fun and rewarding experience, and with the right design and presentation, your robot can demonstrate its capabilities and functionality in a way that will impress your audience.
Read more about robotics here:
https://brainly.com/question/9145476
#SPJ1
as an airplane climbs, do you enrich or lean the mixture to maintain an optimum fuel/air ratio?
Before taking a taxi, the fuel air mixture should be properly leaned to avoid lead deposits on the spark plugs. You'll quickly discover which aircraft in the fleet are more prone to this if you rent an aircraft from an FBO.
Do you lean the mixture or enrich it while an airplane climbs?If you need to climb, enrich the mixture first (if at or above 75% power) before adding power, then lean again after you've reached your desired altitude.
What function does the fuel mixture knob serve?The mixing knob allows you to regulate the amount of gasoline and air entering your cylinders, regardless of whether your engine uses a carburetor or fuel injection. This is significant because the engine requires the ideal mixture of gasoline and air to generate the maximum amount of power.
To know more about spark plugs visit:-
brainly.com/question/28984283
#SPJ4
which osi encapsulation term can be used instead of the term frame
The data unit for the data link layer is a frame, but the transmission unit for the network layer is a packet.
where on the OSI hierarchy The data is contained within frame *?Step 1: In the OSI or TCP/IP paradigm, the Physical layer receives the encapsulated data signals or bits from the sender and de-encapsulates them into a data frame that is then transferred to the Data-Link layer, which is the next tier below.
What does the OSI term "encapsulation" mean?When data is flowing in an OSI or TCP/IP architecture, encapsulation is the process of incorporating extra information. From the application layer to the physical layer, additional information has been added on the sender's end.
To know more about frame visit:-
https://brainly.com/question/28588893
#SPJ4
Which two precautions can help prevent social engineering? (Choose two.) 1) Always require a user name and password to be configured 2) Keep your password securely under your keyboard 3) Escort all visitors 4) Do not allow any customers into the workplace 5) Always ask for the ID of unknown persons
The two precautions that can help in preventing social engineering are as follows:
Keep your password securely under your keyboard.Always ask for the ID of unknown persons.Thus, the correct options for this question are B and E.
What is Social engineering?Social engineering may be defined as the terminology that is considered used for a broad range of malicious activities that are accomplished through human interactions. It is one of the psychological manipulations of people into performing actions or disclosing confidential information.
In the activities of social engineering threats, an attacker generally utilizes certain human emotions to trick the target into performing an action, such as sending the attacker money, disclosing sensitive customer information, or disclosing authentication credentials.
Therefore, the correct options for this question are B and E.
To learn more about Social engineering, refer to the link:
https://brainly.com/question/26072214
#SPJ1
Which of these frequencies has the shorter period? (a) 1 krad/s (b) 1 kHz
1 kHz has the shorter period, as it represents a higher frequency (more cycles per second) than 1 krad/s.
Both 1 krad/s and 1 kHz represent a frequency, but they have different units of measurement.
1 krad/s represents a frequency in terms of radians per second. A radian is a unit of measurement for an angle, and in this context, it represents the number of complete cycles or oscillations per second.
On the other hand, 1 kHz represents a frequency in terms of kilohertz. A hertz is a unit of measurement for frequency, representing the number of cycles or oscillations per second. Kilohertz (kHz) represents a multiple of hertz, where one kilohertz is equal to 1,000 hertz.
To determine which frequency has the shorter period, we need to consider the relationship between frequency and period. Period is the amount of time it takes for one complete cycle or oscillation, and it is measured in seconds.
The relationship between frequency and period is as follows: Period = 1 / Frequency.
To learn more about krad/s, click here:
https://brainly.com/question/29308214
#SPJ4
Floyd’s Bumpers has distribution centers in Lafayette, Indiana; Charlotte, North Carolina; Los Angeles, California; Dallas, Texas; and Pittsburgh, Pennsylvania. Each distribution center carries all products sold. Floyd’s customers are auto repair shops and larger auto parts retail stores. You are asked to perform an analysis of the customer assignments to determine which of Floyd’s customers should be assigned to each distribution center. The rule for assigning customers to distribution centers is simple: A customer should be assigned to the closest center. The worksheet Floyds in the provided datafile contains the distance from each of Floyd’s 1,029 customers to each of the five distribution centers. Your task is to build a list that tells which distribution center should serve each customer. The following functions will be helpful: =MIN(array). The MIN function returns the smallest value in a set of numbers. For example, if the range A1:A3 contains the values 6, 25, and 38, then the formula =MIN(A1:A3) returns the number 6, because it is the smallest of the three numbers: =MATCH(lookup_value, lookup_array, match type). The MATCH function searches for a specified item in a range of cells and returns the relative position of that item in the range. The lookup_value is the value to match, the lookup_array is the range of search, and match type indicates the type of match (use 0 for an exact match). For example, if the range A1:A3 contains the values 6, 25, and 38, then the formula =MATCH(25,A1:A3,0) returns the number 2, because 25 is the second item in the range. =INDEX(array, column_num). The INDEX function returns the value of an element in a position of an array. For example, if the range A1:A3 contains the values 6, 25, and 38, then the formula =INDEX(A1:A3, 2) 5 25, because 25 is the value in the second position of the array A1:A3. (Hint: Create three new columns. In the first column, use the MIN function to calculate the minimum distance for the customer in that row. In the second column use the MATCH function to find the position of the minimum distance. In the third column, use the position in the previous column with the INDEX function referencing the row of distribution center names to find the name of the distribution center that should service that customer.) Click on the datafile logo to reference the data. (Hint: The INDEX function may be used with a two-dimensional array: =INDEX(array, row_num, column_num), where array is a matrix, row_num is the row numbers and column_num is the column position of the desired element of the matrix.) Floyd's Bumpers pays a transportation company to ship its product to its customers. Floyd's Bumpers ships full truckloads to its customers. Therefore, the cost for shipping is a function of the distance traveled and a fuel surcharge (also on a per mile basis). The cost per mile is $2.72 and the fuel surcharge is $.56 per mile. The worksheet May in the provided datafile contains data for shipments for the month of May (each record is simply the customer zip code for a given truckload shipment), as well as the distance table from the distribution centers to each customer. Use the VLOOKUP function to retrieve the distance traveled for each shipment from the exercise completed above, and calculate the charge for each shipment. What is the total amount that Floyd's Bumpers spends on these May shipments? If required, round your answers to two decimal places. $ Check My Work Icon Key Previous Question 7 of 7Problem 10-19 Algo (Some Useful Excel Functions for Modeling)
Consider that it is needed to assign each of Floyd’s customers to a distribution center that is at the closest distance to the customer. The customer zip codes have been given and their distances from each of the five distribution centers in the referred data file “Floyds”.
How to find the shortest distanceSince the interest is in determining the center which is at the shortest distance from the customer, the shortest distance is obtained for each customer. So in the cell G3, use the function written below:
= MIN(B4:F4)
The value obtained is 731. Drag this formula down for all 1029 customers. Now that the minimum distance for each customer has been obtained, it is needed to find out the distribution center for the corresponding distance. For this, first, find the position at which this minimum distance value occurs in the array of five distances. So in cell H4, enter the below formula:
= MATCH (G4, B4; F4, 0)
This function looks for the contents of cell G4 in the range B4 to F4 and returns the position in the array at which it occurs. Since the distance 731 in cell G4 occurs at 1st position in the array of cells from B4 to F4, the function returns value 1 in cell H4. Drag this formula for all 1029 customers.
Step 3/3
Now it is needed to associate each position with the distribution center. For this, use the Index function in cell I4 as below:
= INDEX ($B$2: $F$2, H4)
This function returns the value of the position stated in cell H4 from the range B2 to F2. Now cells B2 to F2 contain the names of all the five distribution centers.
So, by giving this above function, the distribution center is obtained for first customer as Charlotte, NC. Drag this formula for all 1029 customers so that each customer is assigned the nearest distribution center
Read more about distribution centers here:
https://brainly.com/question/28067298
#SPJ1
the area in which a forklift may come in contact with objects or people, either with the rear end or the front forks, is the ______.
The area in which a forklift may come in contact with objects or people, either with the rear end of the front forks, is the work zone.
An instrument used frequently on construction sites to lift heavy objects is referred to as a forklift. Depending on their lifting capabilities, forklifts are built to lift huge items. As work on a given project begins, numerous zones are created to enable the general public to avoid dangerous regions. There are no access points where the general public is prohibited from entering. Work Zones are places where both construction work and other daily activities are carried out. In order to prevent any fatalities, these work zones should take care of safety precautions. Yet, due to a lack of safety measures, some people pass away in these industrial zones every year.
Know more about Work Zone here:
brainly.com/question/14326713
#SPJ4
