Answer:
B. to explain the role of citizens in a fascist state
Explanation:
Benito Mussolini was a Journalist, the leader of the National Fascist Party in Italy as well as the Prime Minister of Italy between 31 October 1922 to 25 July 1943. Benito Mussolini promoted Fascism, a political system that promoted a Corporatist economy where the society is structured according to corporate groups like agriculture, military, science, etc.
In the excerpt above Mussolini was emphasizing on the role of individuals or citizens in a Fascist state. He explained that a Fascist society does not suppress citizens, but rather organizes the nation and has few harmful liberties. In organizing the nation, individuals benefit as their essential liberties are preserved.
Answer:
I’m pretty sure it’s b
. A series RLC circuit containing a resistance of 12Ω, an inductive reactance of 47.13 Ω and a capacitive reactance of 31.83 Ω are connected in series across a 100V, 50Hz supply. Calculate the
Answer:
a) 19.44 ohm
b) 5.14 A
c) 51.9° lagging
Explanation:
A series RLC circuit containing a resistance of 12Ω, an inductive reactance of 47.13 Ω and a capacitive reactance of 31.83 Ω are connected in series across a 100V, 50Hz supply. Calculate the total circuit impedance, the circuits current, power factor
Given that:
R = 12 Ω, [tex]X_L=47.13\ ohm,\ X_C=31.83 \ ohm[/tex], f = 50 Hz,
A) Total circuit impedance (Z) is given by:
[tex]Z=\sqrt{R^2+(X_L-X_C)^2} =\sqrt{12^2+(47.13^2-31.83)^2} =\sqrt{378.09} =19.44\ ohm[/tex]
B) the circuits current (I) is given by:
[tex]I=\frac{V}{Z}=\frac{100}{19.44}=5.14\ A[/tex]
The voltage across the resistor ([tex]V_R[/tex]) = IR= 5.14 × 12 = 61.68 V
The voltage across the inductor ([tex]V_L[/tex]) = [tex]IX_L[/tex] = 5.14 × 47.13 = 242.25 V
The voltage across the capacitor ([tex]V_c[/tex]) = [tex]IX_C[/tex] = 5.14 × 31.83 = 163.5 V
C) The power factor (Θ) is calculated as:
[tex]cos(\theta)=\frac{R}{Z}\\cos(\theta)=\frac{12}{19.44} =0.619\\\theta=cos^{-1}(0.6172)\\\theta=51.9^o\ laggin[/tex]
When discussing universal joints,
Technician A says that they eliminate vibrations caused by the power pulses of
the engine.
Technician B says that they allow the drive shaft to change angles in response
to movements of the car's suspension and rear axle assembly.
Answer:
B only
Explanation:
To prevent hydroplaning, _____. A. slow down B. speed up C. deflate your tires D. use cruise control
Answer:
a. slow down
Explanation:
To properly answer this question, you must understand what hydroplaning is. Hydroplaning is essentially when a car begins to slide on a wet road and the driver cannot control the vehicle. This happens because of an overflow in water on the road which causes the tires to begin to skim on the surface of the water. Having a proper amount of tire tread, typically 5/23 inches deep or above, will reduce chances of a car hydroplaning on a wet surface.
* note:
if you would like a better understanding of what hydroplaning looks like, there are videos on the internet you could watch that show real life footage of what it looks like when cars hydroplane. I recommend searching up 'car hydroplaning.'
Now that we fully understand the question, let's examine each option individually and determine what is the best thing to do to prevent hydroplaning.
option a
slow down
When a persons car begins to hydroplane, it may be going so fast that it becomes difficult to control. Therefore, slowing down to reduce the speed of the car would be your best bet to try and regain control.
option b
speed up
Stepping on the accelerator will increase the speed of the car which will cause it continue to skim on the surface of the water. This may cause the driver to lose even more control of the vehicle.
option c
deflate your tires
Deflating your tires would not be a very reliable option, as it can make you lose control even more. It is also not a guarantee that you would even be able to deflate your tires.
option d
use cruise control
If you put your car on cruise control it can punctually cause you to lose more control and cause your car to increase more speed.
Now that we have gone through each option individually, we can determine that option a 'slow down' is the best thing to do to prevent hydroplaning.
To prevent hydroplaning, slow down. Thus, option A is correct.
What is hydroplaning?When ever a vehicle's tyres hydroplane, they lose traction on the road and move along a thin layer of water that is on the surface of the ground.
A person's car may very well be moving so quickly when it starts to hydroplane that it is challenging to control. In the interest of attempting or regain control, slows to lower the car's speed would be their best choice.
One not only has improved sight but driving more slowly will decrease your risk of hydroplaning. This is so because tyres have more stability at normal revs on wet pavement.
The amount of rain, the type of road, and the state of your tyres will all affect how much slower you should travel. Therefore, option A is the correct option.
Learn more about hydroplaning, here:
https://brainly.com/question/28132317
#SPJ6
