Answer:
Both A and B
Explanation:
The Engine's electronic Control Unit (ECU) gets the instantaneous manifold pressure data from the Manifold Absolute Pressure or MAP sensor which it uses to determine the air density such that the proper engine air mass flow rate is also determined, and from which the allowable fuel flow rate for optimum combustion is established
As such the MAP sensor measures the air mass to establish the fuel injector's base pulse width, which controls the fuel delivery. The MAP sensor also measures intake manifold which is related to the density of the air.
7. In Fleming's left hand rule what do the
following represent:
First finger:
Second finger:
Thumb:
Answer: See explanation
Explanation:
Fleming’s Left-Hand Rule is simply used to know a conductor's direction of force in an electric motor in a scenario where the direction of the magnetic field and the current are already known.
In Fleming's left hand rule, the following are represented:
First finger: This represents the direction of the magnetic field.
Second finger: This represents the direction of the current.
Thumb: This represents the direction of the motion that is acting on the conductor.
Technician A says that the brake pedal should be depressed with as much force as possible during the normal bleeding procedure. Technician B says that the brake pedal should be pumped rapidly during this manual bleeding procedure to force the air down toward the bleeder valve(s). Which technician is correct
Answer:
The appropriate answer is "Neither technician A nor B".
Explanation:
Two consultants or engineers complete the course of treatment A particularly unique upconverter to complement this same master cylinder. The customary static temperature would be used whenever the steering system has always been bleeding would be: 30 psi Two technicians start debating the bleeding atmosphere from either the hydraulic system.Therefore this obvious response is the appropriate one.
Let me help you with your baggage.
If eating three-egg omelets causes weight-gain, budgie eggs are a good substitute.
The waitress was not amused when he ordered green eggs and ham.
Peanut butter and jelly caused the elderly lady to think about her past.
It's not often you find a soggy banana on the street.
his seven-layer cake only had six layers.
I love bacon, beer, birds, and baboons.
We should play with legos at camp.
She did her best to help him.
His son quipped that power bars were nothing more than adult candy bars.
They improved dramatically once the lead singer left.
If you like tuna and tomato sauce- try combining the two. It’s really not as bad as it sounds.
Separation anxiety is what happens when you can't find your phone.
She tilted her head back and let whip cream stream into her mouth while taking a bath.
We have a lot of rain in June.
The father died during childbirth.
He set out for a short walk, but now all he could see were mangroves and water were for miles.
David subscribes to the "stuff your tent into the bag" strategy over nicely folding it.
You have every right to be angry, but that doesn't give you the right to be mean.
He decided water-skiing on a frozen lake wasn’t a good idea.
Answer:
is this free points??????????????????????????????
Explanation:
1. You should
when working with power tools.
A)O Ensure that machine guards are in place
B)O Secure your work with a clamp or vise
C)O Keep your work area clean
D) G Alof the above
You should ensure that machine guards are in place when working with power tools. The correct option is A.
What are power tools?Power tools are those tools that are run by power or electricity. These tools are used when constructing something. These tools are drill machines, cutters, axe, welding machines, etc.
These tools ate used by professionals or used by proper care because they are harmful tools that can lead to accidents. So when using power tools, you should wear helmets, gloves, and goggles to avoid any accidents.
The machine guards are given with the machine, they should be properly installed and used. If not installed or used properly, they can cut or injure you.
Thus, the correct option is A. Ensure that machine guards are in place.
To learn more about power tools, refer to the link:
https://brainly.com/question/11101078
#SPJ2
Which of the following is an acronym used in mechanical plans?
Explanation:
Engineering drawing abbreviations and symbols are used to communicate and detail the characteristics of an engineering drawing. There are many abbreviations common to the vocabulary of people who work with engineering drawings in the manufacture and inspection of parts and assemblies.
Some examples of these are:
BOT: Bottom
B.O.W.: Bottom of Wall
BP: Blue Print (or B/P)
BV: Butterfly Valve
CAD: Cadmium or Computer-Aided Drafting
CBORE: Counterbore
C.C.: Center to Center
C.D.: Construction Document
C.F.M.: Cubic Feet per Minute
CFS: Cubic Feet per Second
C.I.: Cast Iron
E.F.: Exhaust Fan
EQ: Equal, or Equally
E.W.: Each Way
Ext.: Exterior
FACP: Fire Alarm Control Panel
FAO: Finish All Over
the worst time you have had with a mechanical issue
Answer:
When I was taking my sat exam online and my phone battery died
It took my poor dad three attempts to successfully have his truck fixed at the shop before they actually fixed anything.
Three-dimensional measuring references all of these EXCEPT:
radius.
length.
width.
height.
Answer:
Radius. It is only used for Spheres
Explanation:
Technician A says that valve stem height should be checked and the top of the valve ground, if necessary. Technician B says that an incorrect valve stem height may hold the valve open. Which technician is correct
Answer:
Technician A only
Explanation:
The valve stem height is important as the effects of incorrect valve stem height includes;
1) Side thrust
2) Highly recessed valve
3) Effect on the geometry of the combustion chamber
4) Changes in the volume of the combustion chamber
5) The amount of lifter preload
6) The spring height
7) The amount the valve lifts above the valve seat
8) The valve life span
The valve may stay open after the camshaft lobe is moves past the under the lifter when a valve float occurs at high engine speeds
The valve tips can be grinded as recommended by the manufacturer to correct the the valve stem height.
Drawing pictures of possible designs describes which step of the engineering design process?
Answer:
In prototype making first step is to make basic picture of the projrct.
A prototype is an operating version of a solution. Often it is made with different materials than the final version, and generally it is not as polished. Prototypes are a key step in the development of a final solution, allowing the designer to test how the solution will work.
Explanation:
According to the rules of dimension how should written notes appear
Explanation:
Leaders for notes should be straight, not curved, and point to the center of circular views of holes wherever possible. Leaders should slope at 45°, 30° or 60° with horizontal but may be made at any convenient angle except vertical or horizontal.
13. The members installed vertically over and under a window opening are called
studs.
a. Cripple
b. Valley
C. Ridge
Explanation:
Cripples are vertical framing members that support a sill or saddle.
They are installed at points where a common stud would have stood if not for the window opening.
Cripples provide support for the window and the sill it rests on.
any one know the diffrence in a 12v and 24v cummins?
other than the time peorides and the number of vaulve rods
whats the better one?
please dont answer unless u know adout cars
(and Yes katie this is educational)
Explanation:
The 24v is a higher-revving motor, thus you'd probably want the 4:10. The 12v has better low-end grunt and wont spin as fast, so the 3.54 would work better. Bombing is easier with the computer trucks, and cheaper with the mechanical trucks.
24V are much louder than a 12V at the engine.
While the 12-valve is a little bit more reliably with the mechanical P7100 pump, tuning it requires modified parts of the injection pump. The 24-valve might not be as insanely reliable, but it's still very reliable and can easily be tuned with a handheld tuner.
Tech A says that the standard 12-volt car battery has 3 cells with 4.2 volts in each cell. Tech B says that the
standard 12-volt car battery has 4 cells with 3.3 volts each. Who is correct?
Select one:
a. Technician A
b. Technician B
c. Both Technician A and B
d. Neither Technician A nor B
Explanation:
They're both incorrect.
The standard car battery has 6 cells with 2.1 volts a piece.
