whoever answers with a good answer gets marked brainliest

According to the statement, the standard enthalpy change for the reaction at 25°C is ∆H°rxn = -16.3kJ

The change in enthalpy if one mole of a substance is created from its natural components under the same conditions—1 atm of pressure and 298.15 K—is known as the standard enthalpy of formation.

Mg(OH)2(s) + 2HCl(g) ------> MgCl2(s) + 2H2O(g)

∆H°rxn =Σn∆H°f(products) -Σm∆H°f(reactants)

where,

n and m are coefficents of products and reactants respectively

H°rxn = (1mol mol H°f MgCl2 (s) in addition to 2mol mol H°f H2O (g)) - (2mol H°f(HCl(g)) + 1mol H°f(Mg(OH)2(s))

= (1mol × ( -641.8 kJ / mol) + 2 mol ×( -241.8 kJ / mol)) - ( 1mol × -924.5kJ / mol + 2 mol × (-92.30 kJ/ mol) )

= -1125.4kJ + 1109.1kJ

= -16.3 kJ

To know more about standard enthalpy visit :

https://brainly.com/question/14047927

#SPJ1

When the temperature conversion function =CONVERT(-22, "C", "F") is applied, a reading of -22 °C in Fahrenheit is displayed. On a variety of scales, including the Fahrenheit and Celsius systems, temperature is a unit that is used to denote hotness or coolness.

Heat energy will logically go from a hotter (body with a higher temperature) to a colder (body with a lower temperature) according to temperature (one at a lower temperature).

A temperature is a measurement used to express how hot or cold something is. It demonstrates how heat energy naturally flows from a hotter body to a cooler body and can be expressed in terms of any number of arbitrary scales (one at a lower temperature).

A match is burning at a far greater temperature than an iceberg, yet an iceberg has a significantly higher total heat energy than a match. Temperature is not the same as the energy of a thermodynamic system.

The temperature, along with pressure, density, and other similar properties, is referred to as an intense property as opposed to extensive characteristics like mass or volume—one that is independent of the quantity of stuff being addressed.

To know more about temperature:

brainly.com/question/23411503

#SPJ4

The molar mass formula is as follows :

The molar mass = mass / moles  = g/mol

The Molar mass of the  substance is the mass in the grams of the one mole of the compound.  The one mole of the any substance is 6.022 × 10²³ molecules. The standard unit for the molar mass is g/mol. The the SI unit is kg /mol. The formula to calculate the molar mass is as follows :'

The molar mass = mass / moles  = g/mol

The mass of the one atom of the carbon  -12 the atomic mass of the carbon-12 is exactly equals to the 12 atomic mass units. The mass of the one mole of the  carbon - 12 atoms is exactly equals to the 12 grams. the   molar mass is exactly equals to the 12 grams per mole.

To learn more about molar mass here

https://brainly.com/question/22997914

#SPJ4

The characteristic that can be observed in table salt, water, stone, rice and corn is that they are all examples of matter in science.

Matter is characterized by its physical properties, such as mass, volume, density, hardness, malleability, and solubility. Table salt is a solid with a crystalline structure, water is a liquid, stone is a solid with a crystalline or amorphous structure, rice is a granular solid, and corn is a kernel or seed.

It is worth mentioning that the study of matter is of utmost importance to better understand the world and the universe.

See more about matter at https://brainly.com/question/1172629.

#SPJ11

Answer:

Base

Explanation:

In an acid-base reaction, an acid donates a proton (H+) to a base, resulting in the formation of a conjugate base and a conjugate acid. In the reaction H2PO4- + NH3 → HPO42- + NH4+, H2PO4- donates a proton (H+) to NH3, making NH3 the base. The resulting NH4+ ion is the conjugate acid since it was formed by accepting the proton (H+) donated by H2PO4-. H2PO4- is acid, since it donated a proton to NH3, and HPO42- is the conjugate base, since it was formed when H2PO4- lost a proton.

False. From the Stone Age, when stones were employed for hammering and cutting, humans have utilized hand tools. Casting copper and tin alloys allowed for the production of implements throughout the Bronze Period.

Tools made of bronze were more durable and sharp than those made of stone. In the Iron Age, iron took the place of bronze, and tools grew stronger and more resilient. During this time, the Romans created tools that are still being made today.

With the industrial revolution, factory production replaced handcrafting as the primary method of producing tools. Any tool used by craftspeople for manual work is referred to as a hand tool.

Simple tools that you use with your hands and are typically not powered are called hand tools. Any tool that is used manually rather than by a motor is referred to as a hand Examples include drills, vises, clamps, snips, saws, cutters, and files. Hammered or struck instruments also include screwdrivers.

Hand tools come in many varieties and can be used for any task. Certain tools are especially employed for a job, while others are not. Daily tasks need the use of hand tools. Throughout the beginning of time, people have utilized them to carry out a variety of beneficial tasks. It is crucial to understand how Hand tools are made and how to use them properly if you want the finest outcomes for your work. Injuries and errors could result from ignorance.

To know more about Hand tools:

brainly.com/question/15905791

#SPJ4

hand tools are powered instruments, which can be very hazardous when improperly used due to their power source. True/false.

When the aquatic plant elodea was placed in distilled water and a 10% sodium chloride solution the distilled water would cause the plant to swell and the cells wouldn't burst because of the framework cell wall.

When the aquatic plant elodea cells are placed in distilled water (100% water), the water moves inside the elodea cells by osmosis and starts the swelling of the cells. When the elodea cells are placed in a 10% sodium chloride solution, which is hypertonic, the vacuoles disappear and the protoplasm detaches from the cell wall and the organelles appear as clumped in the middle of the cell. The cytoplasm of a elodea cells shrink (Plasmolysis) in response to diffusion of water out of the elodea cells into the herpotnic, the10% sodium chloride solution. The rigid cell wall of elodea cells prevents them from bursting.

Learn more about elodea plant from the link given below.

https://brainly.com/question/29775363

#SPJ4

Option (A) is correct. Bases holding two single strands of DNA together into a double strand of DNA interact through Hydrogen bonds.

The bases holding two single strand of the DNA molecule is held together by hydrogen bonding. These bonding occurs between the nitrogenous bases in the two strands of DNA. The specific base pairings for DNA molecules are the Adenine-Thymine and the Cytosine-Guanine. The DNA double helix is held together by two types of bonds that is covalent bond and hydrogen bond. Covalent bonds occur within each linear strand and strongly bond the bases, sugars, and phosphate groups  that is both within each component and between components. Hydrogen bonds occur between the two strands and involve a base from one strand with a base from the second in complementary pairing in the DNA. These hydrogen bonds in the DNA are individually weak but collectively quite strong.

To learn more about Hydrogen bonding

https://brainly.com/question/1426421

#SPJ4

The complete question is,

Bases holding two single strands of DNA together into a double strand of DNA interact through ___________ bonds.

A. hydrogen

B. covalent

C. chemical carbon

D. ionic

Answer:

To solve this problem, we need to use the balanced chemical equation and the molar mass of Cu and Ag to determine the amount of Cu that reacted and the amount of Ag produced.

The balanced chemical equation is:

Cu + 2AgNO3 → Cu(NO3)2 + 2Ag

From the equation, we can see that 1 mole of Cu reacts with 2 moles of Ag to produce 1 mole of Cu(NO3)2 and 2 moles of Ag. This means that the ratio of Cu to Ag in the reaction is 1:2.

To find the amount of Cu that reacted, we can use the ratio of Cu to Ag and the mass of Ag produced:

Molar mass of Cu = 63.55 g/mol

Molar mass of Ag = 107.87 g/mol

Mass of Ag produced = 89.5 g

Number of moles of Ag produced = mass / molar mass = 89.5 g / 107.87 g/mol = 0.829 mol

Since the ratio of Cu to Ag is 1:2, the number of moles of Cu that reacted is half the number of moles of Ag produced:

Number of moles of Cu = 0.829 mol / 2 = 0.4145 mol

To find the mass of Cu that reacted, we can use the number of moles of Cu and the molar mass of Cu:

Mass of Cu reacted = number of moles of Cu × molar mass of Cu = 0.4145 mol × 63.55 g/mol = 26.32 g

Therefore, 26.32 grams of Cu reacted in the reaction.

Explanation:

According to the stoichiometry , 28.14 grams of precipitate would be formed and the reaction is double displacement reaction.

It is the determination of proportions of elements or compounds in a chemical reaction. The related relations are based on law of conservation of mass and law of combining weights and volumes.

Stoichiometry is used in quantitative analysis for measuring concentrations of substances present in the sample.

212 g sodium carbonate gives 225.15 g Cu₂(OH)₂CO₃

Thus, 26.50 g will give 26.50 ×225.15/212=28.143 g.

Learn more about stoichiometry,here:

https://brainly.com/question/30215297

#SPJ1

Osmosis: Osmosis is the movement of water molecules from a solution with a high concentration of water molecules to a solution with a lower concentration of water molecules, through a cell's partially permeable membrane.

Diffusion: The process of movement of a substance (solid, liquid, or gas) from the region of higher concentration to the region of lower concentration so as to spread uniformly is called diffusion.

Tyndall effect: The Tyndall effect is the phenomenon in which the particles in a colloid scatter the beams of light that are directed at them.

or the scattering of a beam of light by a medium containing small suspended particles.

Brownian motion: Brownian motion refers to the random movement displayed by small particles that are suspended in fluids.

Answer:

The correct order of the statements to describe how fireworks produce color is:

E) The electrons are in the ground state in the atom. This is when the electrons are in the lowest energy level.

A) The element is placed in the flame where energy is added to the electrons.

D) The addition of the energy from the flame makes the electrons go to the excited state. This is when the electrons are in higher energy levels and have more energy.

C) As the electrons return to the ground state, they release electromagnetic energy.

B) The electromagnetic energy that is produced is in the form of light energy, this is the color we see.

F) The electrons in the excited state return to the ground state.

This sequence of events describes how the energy from the flame excites the electrons in the element, causing them to move to higher energy levels. As the electrons return to their ground state, they release energy in the form of light, which is what we see as the color of the fireworks.

Part A) The average number of drops per mL of benzene is 19.33 drops/mL

Part B) The average number of drops for the monolayer is 8.33 drops.

Part C)  0.43 mL of oleic acid/benzene is required to make a monolayer.

Part D)  each drop of solution contains 0.00002 g of oleic acid.

Part E) one drop of oleic acid takes up roughly 0.000022 mL.

Part A)  To find the average number of drops per mL of benzene, add the drops from each experiment and divide by the number of trials:

 (21 drops + 20 drops + 17 drops) / 3  = (19.33 drops/mL)

Part B) We sum the values and divide by the number of values to determine the average number of drops for the monolayer:

 (8 drops + 9 drops + 8 drops) / 3 = 8.33 drops

Part C) To calculate the mL of oleic acid/benzene required to produce a monolayer, multiply the average number of drops required for the monolayer by the mL per drop of benzene determined in Part A:

8.33 drops x (1 mL / 19.33 drops) = 0.43 mL

Part D) Using the concentration of the solution, we can determine how many grams of oleic acid are in one drop of the solution:

0.02 g/L = 0.00002 g/mL

Because the density of the solution is not specified, we presume it is the same as that of benzene, which is 0.879 g/mL. As a result, the mass of one mL of solution is:

0.879 g/mL x 1 mL = 0.879 g

The mass of oleic acid in one drop of the solution may now be calculated:

0.00002 g/mL / 1 mL x 1 drop = 0.00002 g/drop

Part E) We need to utilise the density of oleic acid, which is 0.895 g/mL, to calculate the volume in mL that one drop of oleic acid occupies:

0.00002 g / 0.895 g/mL = 0.000022 mL

For more such questions on benzene, click on:

https://brainly.com/question/14788042

#SPJ4

The probable question may be:

Part A) Using a graduated cylinder, you calibrate the pipet you will be using and the values you collect are as follows. What is the average number of drops per mL of benzene.

21 drops

20 drops

17 drops

part B) After calibration, you use the oleic acid/benzene solution to form a monolayer. It takes 8 drops , 9 drops and 8 drops before the layer on the water solution starts to make a bubble that does not go into solution. What is the average number of drops for your monolayer?

part C) Since we have the number of drops it takes to make a monolayer and we have the number of drops it takes to make one mL of benzene, we can determine the mL of oleic acid/benzene it takes to form a monolayer.

part D) Next we need to determine the mass of oleic acid in the monolayer. The concentration of the oleic acid/benzene solution is 0.02g/L. Calculate how many grams of oleic acid is in one drop.

part E) With this information, we now need to calculate the volume in mL the drop of oleic acid occupy using the density of 0.895 g/mL and the number of drops of oleic acid solution used.

The composition of a mixture of two components that generates the lowest possible melting point describes eutectic composition.

The precise combination of at least two solid components that, at a certain temperature, causes a change in phase to liquid is known as a eutectic composition. This temperature, also known as the eutectic point temperature, is the minimal melting point for all conceivable compositions.

When a solid solute, a solid solvent, and a liquid mixture all exist in the same phase, that point is known as the eutectic point. The lowest temperature at which the liquid phase is stable at a specific pressure is known as the eutectic point.

For soldering, eutectic alloys are frequently employed. By mass, a typical composition consists of 63% tin and 37% lead. Very strong and resistant to corrosion are eutectoid glassy metals.

To know more about Eutectic composition, check out:

https://brainly.com/question/14785045

#SPJ1

The pure water is considered as the neutral substance as the positive and negative ions balance each other out. The correct option is D)

The H₃O⁺ is called the hydronium ion, and it will makes the acidic in nature. The OH⁻ ion  is called as the hydroxyl ion and it will makes the basic in nature. In the water, there is thein  balance between the hydroniums and the hydroxyls so they will cancel out each others' charges. Therefore the Pure water is neither the acidic in nature or the basic.

Thus, the pure water is the neutral in nature and the value on the pH scale is 7.

To learn more about water here

https://brainly.com/question/1216922

#SPJ4

Therefore, the rate of effusion of carbon monoxide under the same conditions is approximately 6.05 mol/s.

Pressure is defined as the amount of force per unit area. It is a measure of how much force is distributed over a given surface area. Pressure can be represented by the symbol P and is typically measured in units such as Pascals (Pa), pounds per square inch (psi), or atmospheres (atm). Pressure is a fundamental concept in physics and is involved in a wide range of phenomena, from the behavior of fluids to the operation of mechanical devices. For example, when a force is applied to a gas, the gas molecules collide with the walls of the container and exert a pressure on the walls. This pressure is proportional to the number of gas molecules, the temperature of the gas, and the volume of the container.

Here,

The effusion rate of a gas is inversely proportional to the square root of its molar mass. This means that if we know the ratio of the molar masses of two gases and the effusion rate of one gas, we can use that information to determine the effusion rate of the other gas.

Let's assume that the effusion rates of helium and carbon monoxide are related by the following equation:

Rate of Helium / Rate of Carbon Monoxide = sqrt(Molar Mass of Carbon Monoxide / Molar Mass of Helium)

We are given that the rate of effusion of helium is 16.0 mol/s, so we can use this value and the molar masses of helium (4.00 g/mol) and carbon monoxide (28.0 g/mol) to solve for the rate of effusion of carbon monoxide:

Rate of Helium / Rate of Carbon Monoxide = √(Molar Mass of Carbon Monoxide / Molar Mass of Helium)

16.0 mol/s / Rate of Carbon Monoxide = √(28.0 g/mol / 4.00 g/mol)

Simplifying the right-hand side, we get:

16.0 mol/s / Rate of Carbon Monoxide = √(7)

Squaring both sides, we get:

256 mol²/s² = 7 Rate of Carbon Monoxide²

Dividing both sides by 7, we get:

Rate of Carbon Monoxide² = 36.57 mol²/s²

Taking the square root of both sides, we get:

Rate of Carbon Monoxide = 6.05 mol/s

To know more about pressure,

https://brainly.com/question/18431008

#SPJ1

If 1.0 g of cesium-137 disintegrates over a period of 150 years, then g of cesium-137 that would remain is : 0.03125 g.

Half-life is the time required for a quantity (of substance) to reduce to half of initial value and the term is used in nuclear physics to describe how quickly unstable atoms undergo radioactive decay .

90 years is 5 half lives because one half life is 30. So after 30 years, Fraction Remaining (FR) = 0.5^n,  n is the number of half lives that have elapsed.

In the current problem we want to find the FR, and we know n = 5 half lives elapsed (150 yr/30yr = 5)

FR = 0.5^n = 0.5⁵= 0.03125

As we started with 1.0 g, and we have 0.03125 left, that would be 1.0 g x 0.03125 = 0.03125 g.

To know more about half life, refer

https://brainly.com/question/1160651

#SPJ1

Answer:

All of the above. According to the Kinetic Molecular Theory, the gas particles in this container behave in an elastic manner, meaning that they will bounce off each other and the walls of the container without losing energy. The kinetic energy of the gas particles is also dependent on temperature, meaning that the higher the temperature, the faster the particles will move. Finally, energy is not lost when gas particles collide with each other or the walls of the container.

Energy is not lost when gas particles collide with each other or with the walls of the container. Therefore, all of the above are correct.

The gas laws mentioned in earlier modules of this chapter are adequately explained by the kinetic molecular theory (KMT), a straightforward microscopic model. The five postulates listed below form the foundation of this theory.

Although certain gases, like the noble gases, are made up of atomic species, the term "molecule" is going to be employed to refer to the specific chemical species that make up the gas. Gas particles are elastic and do not attract each other. The kinetic energy of gas is dependent on temperature. Energy is not lost when gas particles collide with each other or with the walls of the container.

Therefore, all of the above are correct

To know more about kinetic molecular theory, here:

https://brainly.com/question/134712

#SPJ2

The energy stored in chemical bonds of a molecule that can be used to make new bonds in a different molecule is called chemical potential energy.

When a chemical reaction occurs, the reactant molecules have a certain amount of chemical potential energy stored in their bonds, and this energy is either released or absorbed as new bonds are formed in the product molecules. The amount of chemical potential energy stored in a molecule depends on the types and arrangements of atoms in the molecule, as well as the strength of the chemical bonds between them.

The strength of the chemical bonds in a molecule depends on several factors, including the types of atoms involved, the number and arrangement of electrons around those atoms, and the way in which those electrons are shared or transferred between the atoms to form the bond. Bonds that involve the sharing of electrons, such as covalent bonds, tend to be stronger than bonds that involve the transfer of electrons, such as ionic bonds.

Chemical reactions occur when reactant molecules come into contact with one another and the energy stored in their chemical bonds is either released or absorbed as new bonds are formed in the product molecules. The energy released or absorbed during a chemical reaction is known as the enthalpy change, and it reflects the difference in the total chemical potential energy between the reactant and product molecules.

Learn more about chemical bond here:

https://brainly.com/question/11527546

#SPJ4

Acetaminophen, usually referred to as paracetamol, is the substance that makes Tylenol active. It functions as a painkiller and fever reducer by preventing the body's generation of certain molecules that ingredient

A material that is included into the creation of a product or combination is known as an ingredient. An active component in a medicine is the chemical molecule that gives the drug its therapeutic effects. Excipients usually referred to as inactive substances, are added to medications for a number of reasons, including to aid in absorption, enhance flavour or texture, or lengthen shelf life. A drug's purity and quality of components determine its effectiveness and safety. In particular, if you have allergies or are taking other drugs that might interfere with the active or inactive substances, it is crucial to thoroughly read the label and go through any concerns with a healthcare professional.ingredient

Learn more about  ingredient here:

https://brainly.com/question/30141107

#SPJ4

Lattice energy must have a positive energy change. Option E is correct choice.

Lattice energy is the energy required to separate one mole of a solid ionic compound into its constituent ions in the gas phase. This process requires energy as the positively charged metal ions and negatively charged nonmetal ions are attracted to each other in the solid lattice structure.

The energy required to break these attractive forces and separate the ions is called the lattice energy. Since this process requires energy, the lattice energy change must be positive. Therefore, option e is correct answer.

To know more about the energy change, here

brainly.com/question/22255429

#SPJ4

Serous fluid is a clear, watery fluid produced by serous membranes. Serous membranes are thin and slippery membranes that also functions as line the cavities of the body and cover its organs.

Serous fluid actually helps to reduce the friction between organs and the surrounding structures. This allows them to move smoothly and the friction is reduced so no rubbing against each other.

The main component of serous fluid is water. It also contains small amounts of electrolytes, proteins, and other substances.

Serous fluid is produced by cells in the serous membranes. They continuously secrete the fluid into the cavity between the two layers of the membrane.

In the pleural cavity (the cavity which surrounds the lungs) there is serous fluid present and it allows the lungs to expand and contract smoothly during breathing, without rubbing against the chest wall or the diaphragm.

Learn more about Serous fluid:

https://brainly.com/question/30462607

#SPJ4

As a result of the inherent reaction specificity, stereoselectivity describes the preferential formation of one merchandise stereoisomer (enantiomer or diastereomer) compared to another during a chemical reaction.

Stereoisomers, by definition, are isomers having a same composition (i.e., same parts), but distinct spatial orientations. Stereoisomers come in two main varieties: enantiomers and diastereomers.

Several sets of molecules attached to a central core have varied relative orientations, which leads to the formation of stereoisomers. Stereoisomers include drugs like R- and S-thalidomide.

To know more about stereoisomer visit:

https://brainly.com/question/16986110

#SPJ4

Compounds have fixed composition, properties and are chemically bonded while mixtures have variable composition, properties and are physically mixed.

Mixtures and combinations are two distinct sorts of substances. Compounds are unadulterated substances made out of at least two components synthetically reinforced together in a decent proportion, while blends are blends of at least two substances that are truly blended yet not artificially consolidated. Three manners by which mixtures and combinations vary are:

Piece: Mixtures have a proper creation and a particular proportion of molecules or particles, while blends have a variable synthesis with no particular proportion.

Properties: Mixtures have unmistakable properties, like a particular dissolving point, edge of boiling over, and compound reactivity, while blends have a scope of properties that rely upon the substances in the combination.

Detachment: Mixtures must be isolated by substance implies, like through a compound response, while blends can be isolated by actual means, like filtration, refining, or chromatography.

To learn more about compounds, refer:

https://brainly.com/question/28696140

#SPJ4

The equation for the dissociation of the weak acid HBrO[tex]_4[/tex] in water is HBrO[tex]_4[/tex] + H[tex]_2[/tex]O [tex]\rightarrow[/tex] BrO[tex]_4[/tex]⁻. Perbromate salts are created when it interacts with bases.

The inorganic substance with the equation HBrO[tex]_4[/tex] is perbromic acid. It is a bromine oxoacid. Unlike periodic acid, which is manufactured by displacing chlorine with perchloric acid, perbromic acid highly unstable and can only be created by protonating the perbromate ion.

Very oxidizing and an acid, perbromic acid is. It is the halogen(VII) oxoacid that is most unstable. When exposed to air and bromic acid, it breaks down quickly. Perbromate salts are created when it interacts with bases.

HBrO[tex]_4[/tex] + H[tex]_2[/tex]O [tex]\rightarrow[/tex] BrO[tex]_4[/tex]⁻

Therefore, the equation for the dissociation of the weak acid HBrO[tex]_4[/tex] in water is HBrO[tex]_4[/tex] + H[tex]_2[/tex]O [tex]\rightarrow[/tex] BrO[tex]_4[/tex]⁻.

To know more about per bromic acid, here:

https://brainly.com/question/11003770

#SPJ1

To cause cancer, proto-oncogenes require 1 allele to be mutated and are therefore considered dominant.

Cancer is a group of diseases involving abnormal cell growth with the potential to invade or spread to other parts of the body. These contrast with benign tumors, which do not spread. Possible signs and symptoms include a lump, abnormal bleeding, prolonged cough, unexplained weight loss, and a change in bowel movements.While these symptoms may indicate cancer, they can also have other causes.Over 100 types of cancers affect humans.

Tobacco use is the cause of about 22% of cancer deaths. Another 10% are due to obesity, poor diet, lack of physical activity or excessive drinking of alcohol. Other factors include certain infections, exposure to ionizing radiation, and environmental pollutants.

Learn more about cancer,here:

https://brainly.com/question/8590464

#SPJ1

The correct name for the given compound S4P2 is- option B( tetrasulfur diphosphide).    

When two or  further  rudiments chemically combine in a fixed  rate by mass, the  attained product is known as a  emulsion. Composites can be defined as substances  conforming of 2 or  further different types of  rudiments in a fixed  rate of their  tittles. When the  rudiments combine, some individual property of the  rudiments is lost and the  recently formed  emulsion has new  parcels. composites are represented by their chemical formula. A chemical formula is a emblematic  representation of the proportions of  tittles that constitute a particular chemical  emulsion.  The prefix" tetra-" indicates that there are four sulfur  tittles, and the suffix" ide" indicates that the  emulsion contains two phosphorus  tittles.

For such more questions on Compound

https://brainly.com/question/26388921

#SPJ4

The end result of glycolysis is the production of two molecules of pyruvate or pyruvic acid i.e CH₃COCOOH, two molecules of ATP, and two molecules of NADH. Option B is correct.  

Pyruvate is a three-carbon molecule that can be further metabolized through the Krebs cycle and oxidative phosphorylation to produce more ATP.

Glycolysis is important because it is the first step in the breakdown of glucose to extract energy for cellular metabolism. Glucose is a major source of energy for most living organisms, and glycolysis provides the initial breakdown of glucose to produce ATP.

This process can occur in the absence of oxygen, which is essential for cells that cannot access oxygen. In addition, the two ATP molecules produced in glycolysis provide immediate energy for cellular processes, and the NADH molecules produced can be used to generate more ATP through the subsequent steps of cellular respiration.

Hence, B. CH₃CO.COOH is the correct option.

To know more about glycolysis here

https://brainly.com/question/14076989

#SPJ4

--The given question is incorrect, the correct question is

"what is the end result of glycolysis? why is this step important? A) CH₃CH₂OH B) CH₃CO.COOH C) CH₃HCOH -- COOH D) CH₃CH₂COOH"--

The label of the periodic table is that the Groups are labeled at the top of the each column and the horizontal rows are called as the periods.

The elements are arranged in the seven horizontal rows, that are called as the periods or the series, and there are the 18 vertical columns that are  called as the groups. The Groups are labeled at the top of the each column. The labelled parts of the element in the periodic table will tells the atomic number and the atomic mass of the element.

The upper labelled part is  the atomic number of the element and The lower part is the atomic mass of the element in the periodic table.

To learn more about periodic table here

https://brainly.com/question/28997280

#SPJ4